Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Dyno Power

So you reckon you know how much grunt your engine's got? Are you sure?

By Andrew Elder*

Click on pics to view larger images

This article was first published in 1999.

Dyno Calibration

The first question must be: how accurate is the measuring system? When was the dyno last calibrated? What calibration weights were used for the calibration? Are their weights accurately known? Was the effective length of the torque calibration arm measured accurately? If the arm was assumed to be 610mm from the centre-line of the dyno main shaft to the hang-down point, but was actually only 603mm, the power reading would differ by about 1 per cent. Was the dyno measurement system checked for linearity? Some dynos, particularly those using dashpot-pressure torque read-outs, having varying accuracy depending on the applied torque.

Is the measured torque affected by the temperature of the measuring load cell? On some dynos the temperature of the load cell is affected by the absorber and/or exhaust system temperatures. This can lead to inaccuracies.

With a water-brake dyno, was the residual torque reading zero with the engine stopped? Drag from the water supply and discharge plumbing can create a significant torque offset error.

Atmospheric Correction

Were the reported torque and power figures corrected for atmospheric conditions? What correction standard was used? Just changing the correction standard between SAE and DIN can result in a 0.7 per cent change in power for exactly the same engine. How accurately was the barometric pressure, air temperature and relative humidity measured? Where was the air temperature measured? A 5ºC inaccuracy in air temperature can lead to a 0.9 per cent change in power figures. A 3mB (normal range 900 to 1050mB) inaccuracy in barometric pressure gives a 1 per cent change in power.

Engine Ancillaries

Was the engine tested with the alternator, fan, airconditioning compressor, power steering pump etc connected? This is very important when comparing power figures from different dyno shops.

The Test

Was the engine tested in the same tune and conditions on the dyno as when it was returned to the customer? What fuel was used when tested on the dyno? Was the ignition timing "tweaked" on the dyno, but retarded again when delivered? Was the same exhaust system used on the dyno as was used in the vehicle?

What oil and water temperatures were used for the test? Lower water and higher oil temperatures can produce higher power from an engine, but what of the long term effects on the life of the engine?

If using a chassis dyno, what gear was used?

Was the engine tested to its peak reported power, or was the peak power figure extrapolated (read guessed) from lower speeds on a "speed challenged" dyno unable to run at maximum engine/vehicle speed?

On forced-induction engines, was the boost limit as tested the same as that when delivered?


The peak power figure for a given engine is only one measure of its performance. One engine may have a higher peak power compared to another, but may be slower on the road or track. A better indicator of performance is the average power over the normal speed range of the engine.

For example, a "peaky" engine might produce say 300bhp at 7000 rpm, and an average power form 5000 to 7000 of 260 bhp. A less peaky engine might produce 280 bhp at 7000 rpm, but an average of 270 bhp over the same speed range. Clearly an engine is at 7000 rpm for only a brief time in the real world, so the "less powerful" 280 peak bhp engine will perform better on the road, and also be a nicer engine to drive.


Many aspects of engine performance testing can influence the "bottom line" power figure and its relevance to overall vehicle performance. The quoted peak power figure is only a part of the total picture.

*Arex Computing, dyno software development specialists. Contact:
+613 9751 1142

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
A unique solution to reducing vibration in driving lights

DIY Tech Features - 16 October, 2012

Mounting big driving lights, Part 2

What is the best way forward for car propulsion systems?

Technical Features - 2 November, 2007

Alternative Cars, Part 8

Planning, earthworks and site access - beginning the home workshop build

DIY Tech Features - 19 August, 2008

Building a Home Workshop, Part 2

How to use taps and dies

DIY Tech Features - 7 April, 2006

Making Things, Part 4

The unique front suspension

DIY Tech Features - 26 May, 2009

Chalky, Part 3

Forming a curved body without moulds or panel beating

DIY Tech Features - 10 February, 2009

Building an Ultra Light-Weight Car, Part 2

The very first production turbo car - the Oldsmobile Jetfire

Special Features - 7 June, 2003

The Early Days of Turbo Part 4

Looking at the worth of bio-fuels

Special Features - 17 April, 2008

Biofuels: Friend or Foe

Lunar Rover: the only car literally out of this world

Special Features - 14 October, 2008

World's Greatest Cars, Part 2

Assessing the performance of an amazing human powered vehicle

DIY Tech Features - 15 January, 2008

Air 150 Recumbent Trike, Part 2

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip