Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Salvaging Bits from Wiring Looms

Lots of useful wiring bits at a very low cost

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Salvaging stuff from old wiring looms
  • Plugs
  • Grommets
  • Relay boards
  • Fuse boxes
  • Fasteners
Email a friend     Print article
This article was first published in 2004.

Click for larger image

Head off to a wrecker and you’re sure to see some wiring looms sitting around. Often they’ve been cut to get them out of the car and as a result, the wrecker sees them as worth nearly nothing. For example, I’ve bought three large looms in the last few months at AUD$10 each.

So what good are they then? Well, you can get a whole heap of good parts from a wiring loom – let’s take a look.

Firewall Grommets

If you’ve ever installed programmable management, an interceptor – or even just wanted to feed a whole heap of new wires through the firewall – you’re sure to have come up against the problem of sourcing an appropriate grommet. Off the shelf hardware store items aren’t usually suitable because (a) they’re not big enough and (b) they don’t have the ‘tail’ that makes proper firewall grommets weatherproof. But in a typical wiring loom you’re sure to find one or two that are suitable.

Click for larger image

There are those that look like this...

Click for larger image

...or larger oval-shaped ones like this.

Click for larger image

Some looms even have firewall grommets that are backed by a metal plate that bolts to the firewall.

Sensor Plugs

Want to install an extra injector? Or swap an airflow meter? Often you’ll find that sourcing the plug is the hardest part of the modification. But if you pick a loom that’s from your make and model of car (or often any model from your car’s manufacturer that was produced at about the same time) you’ll find the right plugs in abundance.

Click for larger image

This loom has ECU plugs....

Click for larger image

...and an airflow meter plug.

Click for larger image

You’ll also find two-pin plugs...

Click for larger image

...and other two-pin plugs to suit injectors. In short, there’s plenty of plugs of a myriad different designs!


Even if most of the components have been unplugged, many harnesses have relays still attached. Because they come with a dedicated plug and a length of cable, they’re easy to add to your car while still looking factory and professional.

Click for larger image

This relay comes with wiring, plug and bracket while...

Click for larger image

...this design has a rubber shroud that can easily be mounted on a custom made vertical bracket (it slides in where the arrow is).

Click for larger image

And if you want a full relay board, try this out for size! Often the individual relays and their dedicated holders can be removed – handy if you don’t need a massive relay upgrade to the wring.

Click for larger image

Dedicated fuse boxes can be found in nearly all discarded wiring looms. Here’s how a fusebox salvaged from a loom was used in the installation of a high-powered intercooler fan. The fusebox contains two high-current fusible links.

Click for larger image

This fusebox is perfect for a general purpose upgrade – it has some fusible links, fuses and a relay.


If you want to make new wiring look factory, you’ll need to use factory-style fasteners to hold it in place. (This is so much nicer than just cable-tying it to existing wiring!)

Click for larger image

A variety of fasteners is used on looms – here the top one is designed to clip into a drilled hole while the bottom attaches over the exposed thread of a bolt. In both cases the loom is easily attached to the fastener with normal electrical tape.

Click for larger image

This loom fastener comes with its own plated bracket.

Click for larger image

This fastener is designed for a bulky loom and clips into a panel hole. It is easily undone from the existing loom.


And don’t forget that when you buy an old wiring harness you’re also acquiring a huge amount of useful insulated wire!

Click for larger image

As can be seen here, there’s a wide variety of gauges, suitable from handling heavy battery loads right through to wiring-in sensors.

Click for larger image

Sometimes heavy duty lugs will already be crimped to the ends of the thickest cables – very useful as getting a good crimp or solder connection can be difficult on heavy-duty cables.

Bits and Pieces

Click for larger image

And you’ll also find convoluted tube in a variety of sizes, multi-pin plugs and sockets (used to connect parts of the loom), in-harness fusible links, battery terminals – and a whole lot more.


If you can pick up a wiring loom for a few bucks – especially if it’s your car’s make or model – do it. Put it to one side then when you need a fusebox, or a relay socket, or even just a length of small diameter convoluted tubing or some fasteners, dig it out. The on-car wiring job will look and work so much better.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
How Mitsubishi developed the vortex generators on the Lancer

Special Features - 3 October, 2006

Blowing the Vortex, Part 2

Not a flat six in sight...

Feature Cars - 3 March, 2009

The Electric Porsche

A brilliant do-it-yourself handheld spotlight or bike headlight

DIY Tech Features - 11 February, 2008

Building a High Performance LED Lighting System, Part 1

Measuring analog and digital signals

DIY Tech Features - 24 February, 2009

How to Electronically Modify Your Car, Part 11

The technology of Nissan's famous twin turbo V6

Technical Features - 28 February, 2008

The Nissan VG30DETT

Igor Sikorsky's brainchild

Technical Features - 18 May, 2010

The First Helicopter

Using a prebuilt DIY electronic module to flash high intensity LEDs

DIY Tech Features - 14 July, 2008

Bike LED Lighting Power!

An auto trans cooler that will cost you almost nothing

Technical Features - 12 February, 2008

Cooling the Trans

A breakthrough car that proved to be a step too far

Special Features - 6 August, 2008

The NSU Ro 80

Turning the voltage switch into a standalone temperature or light switch

DIY Tech Features - 29 July, 2008

The eLabtronics Voltage Switch, Part 2

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip