Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Useful Ideas

Ten good ideas

by Julian Edgar

Click on pics to view larger images

This article was first published in 2008.

Some things don’t change. I recently bought Useful Ideas, published in 1952 by Popular Mechanics magazine. The book contains hundreds of hints and tips for those working with their hands. Here are ten of them.

Grommet Cushions Drill Chuck

Click for larger image

When using a drill to make holes in thin sheet, the sudden breaking-through of the drill bit often results in the end of the chuck impacting the work, ruining the finish of the sheet. To avoid this occurring, fit a rubber grommet over the drill-bit – this cushions the impact.

Taking the Slop Out of Vice

Click for larger image

Especially when worn, a bench vice can have lots of slop in the thread. This doesn’t cause any problem when the vice is tightened, but it can make the initial clamping difficult, especially if you’re trying to insert a ‘sandwich’ of pieces in the jaws. To overcome the thread slop, remove the front half of the vice and place a compression spring over the threaded rod before reassembling. The slop will be gone.

Avoid Finger Pinches

Click for larger image

And another vice hint. It’s easy to pinch your fingers in a vice handle, especially when the handle unexpectedly slides downwards through the shaft hole. However, it’s simple to avoid this by slitting a short length of rubber hose and slipping it over the handle, one each side of the main shaft.

Storing Tiny Things

Click for larger image

Storage doesn’t get much cheaper than this. If you need to store sorted tiny objects (like circlips, tiny nuts and screws, etc) just buy a couple of fridge ice cube trays. They’ll stack on top of each other and keep all the bits and pieces in their right places. And they’re much cheaper than buying specialised screw trays!

Sawing Thin Metal

Click for larger image

Cutting thin metal with either a bandsaw or jigsaw can be problematic as the metal tends to chatter. But if you sandwich it between two sheets of scrap hardboard, the chatter stops. The pattern that’s being followed in the cutting can be marked on the upper hardboard, allowing you to still cut accurately. Screw the sandwich together, inserting the screws through the waste part of the job.

Custom Hex Key Tool

Click for larger image

If you regularly work on a machine that uses just three or four sizes of hex-key bolts, here’s a handy tool you can make. Cut across a large nut two vees at right angles to one another. Cut the hex keys to an appropriate length and lay them in the vees, welding or brazing them in place. Grind the welds back for a smooth finish. Ensure that during the welding the working ends of the keys don’t get too hot and so have their temper ruined.

Flush Cutting of Bolts

Click for larger image

If you need to cut off a bolt flush with a surface, turn the blade of a hacksaw sideways and then use two blocks of wood to offset the blade further downwards. The saw is then held as for normal use but with pressure applied sideways.

Hand Bending Tube

Click for larger image

If bending soft tube like aluminium or copper, use two different sized V-pulleys mounted slightly apart on a board. By working the tube between the pulleys, different radii bends can be easily formed with much less chance of the tube kinking.

Sanding Nooks and Crannies

Click for larger image

If you need to sand a recessed grove or inner corners of a box, use a pencil of the type that has an eraser on one end. Wrap a thin width of sandpaper around the rubber and you’ll be able to reach those otherwise hard to reach places.

Using the Other End of the Vice

Click for larger image

If you have a need for a bar clamp, one can be quickly improvised by using the rear end of a bench vice. A G-clamp is used to make a ‘stop’, with the items to be clamped placed between the stop and the back end of the open vice. The vice is then screwed closed, pressure being applied to the clamped object.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Will we one day all be driving solar powered cars? Nope!

Technical Features - 19 September, 2007

Alternative Cars, Part 2 - Solar

How to get the best out of a bench grinder

DIY Tech Features - 8 July, 2008

Using Bench Grinders

One of the best electronic car modification tricks you ever saw

DIY Tech Features - 15 October, 2013

Pots aren't just variable resistors

Improve BOTH power and fuel economy!

DIY Tech Features - 9 September, 2008

Auto Air Conditioner Controller

How the air moves under a car

DIY Tech Features - 9 March, 2005

Modifying Under-Car Airflow, Part 1

Igor Sikorsky's brainchild

Technical Features - 18 May, 2010

The First Helicopter

How tyres really work on the road

Technical Features - 9 August, 2007

Tyres, Grip and All That

Introducing a breakthrough in DIY electronics

DIY Tech Features - 6 October, 2009

eLabtronics EZ System, Part 1

So what's detonation and how can it be detected?

DIY Tech Features - 2 November, 1999

DIY Detonation Detection Part 1

Single-handedly erecting the framework for a home workshop

DIY Tech Features - 26 August, 2008

Building a Home Workshop, Part 3

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip