Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


XR6T Beyond 1000hp!

We take a look at the Nizpro XR6T engine which rips out in excess of 1000hp - along with fat, useable torque and reliability.

Words by Michael Knowling, Pix by Julian Edgar

Click on pics to view larger images

At a glance...

  • 1035hp from a Ford XR6T engine
  • Fat, useable torque curve
  • High strength internals
  • 7500 rpm limit
  • AUD$40k+ build
  • The absolute XR6T benchmark
Email a friend     Print article
This article was first published in 2004.

Click for larger image
See bottom of article for video download of this dyno run!

If there’s one thing we’ve learnt about Simon Gichus of Nizpro it’s that he’s more than willing to spend the time and money developing the most super-duper tuned engines. Every time we have a peek inside his fully equipped dyno cell there’s something wild bolted to the engine stand.

The last time we poked our heads into the dyno cell we happened to see this – Australia’s most powerful Ford XR6 Turbo engine!

With a last run of 1035hp – running a mild 23 psi boost and with Mobil 98 RON fuel – Simon has been the first to crack the magic tonne. Interestingly, Simon says there will be quite a few people making big power with XR6Ts in the next few years. “We wanted to get in early and develop something that will make that 1000hp figure while still holding together and being nice an’ driveable,” he says.

Click for larger image

Simon was drawing on his wealth of experience tuning Nissan RB-series engines when he tackled the new Ford six. “At 4.0 litre it’s a big engine and, in that context, it can rev alright with the right gear – we plan on taking it to around 8000 rpm.” And that takes us to one very important point. Simon says that achieving 1000hp+ reliably calls for a fine balance of torque and revs.

“We’ve held to an 800ft-lb torque limit, which we aim to get up to and maintain as far through the rev range as possible. This should protect the rods and various other parts of the engine, compared to sticking in more and more boost and watching torque go up,” he says.

With this in mind, the engine has been built to withstand high rpm as well as huge torque.

Click for larger image

The standard crankshaft has been replaced by a fully counterweighted steel billet crankshaft, which Simon had manufactured locally. Rods are H-beam forged items working with local forged pistons. These provide an 8.3:1 static compression ratio (0.4 lower than standard) and slide in 0.05mm oversize bores. Rings are described as “special”.

The Ford DOHC has been slightly modified. “compared to a Nissan GT-R head, in standard form the XR6 head flows about 12 percent better on the inlet and 15 percent better on the exhaust.” Cam specs are a closely guarded secret but we can tell you upgrade valve springs are necessary.

Click for larger image

Simon was concerned by possible oil starvation of the big-end bearings and has modified the oil system. An oil cooler is fitted for dyno use and will be retained once the engine is fitted to a car (Simon will be dropping the engine into his everyday XR6T ute for on-road trials!).

Click for larger image

The whole purpose of an engine dyno is to allow extensive engine development. Simon has used his dyno to good effect, having tried three other turbochargers before settling on the current jigger. And, no, Simon isn’t going to give that info away... Likewise, the exhaust manifold design is a secret but Simon tells us fabrication of a compact, 6 cylinder turbo manifold is a very difficult exercise.

Simon went with his preferred approach to boost control – the combination of a wastegate and pressure relief valves on the intercooler plumbing. A 44mm Teal external wastegate and a pair of ex blow-off valves serve to maintain the desired turbine speed. Maximum boost pressure is about 23 psi, but Simon generally tips in a couple of psi more boost through the top-end to maintain his desired torque figure.

Click for larger image

Intercooling in the dyno cell is left to a water-to-air arrangement. This provides a thermostatically-controlled 40 degrees C intake temp charge that we’re told is representative of what you’d find in a car with a front-mount air-to-air intercooler.

Pre-compressor intake flow is almost restriction-free thanks to a huge K&N pod filter, while a 4 inch dump pipe lets the turbine breathe. According to Simon, this flows similarly to the twin 3 inch set-up currently used in his car.

Click for larger image

The intake manifold is the same set-up used in the off-the-shelf Cobra 3 kit. Nizpro has developed a replacement intake upper section of manifold that mates to the factory lower section. This replacement part features a revised internal volume and the factory Ford throttle is relocated to one end of the manifold.

Click for larger image

The complete replacement engine management system is the only one on the market that’s up to the task of controlling the Ford’s electronic throttle and variable cam timing: a MoTeC M800.

Mapping of throttle strategies will probably be finalised when the engine hits the road, but – for now – Simon says the ability to alter cam overlap (by altering the relationship between inlet and exhaust cams) makes a huge difference. In the bottom-end, at about 2000 rpm, Simon has picked up around 100ft/lb...

Click for larger image

When teamed with the factory rail, lines and regulator, a massive set of ‘drop in’ injectors provide the necessary fuel flow. Twin Bosch 984 fuel pumps maintain flow and pressure.

The ignition remains completely stock, except the plug gap is dropped from 1.0mm to 0.9mm.

Running straight Mobil 98 RON fuel, the mega XR6T engine has recently turned Nizpro’s DynoLog engine dyno to the tune of more than 1000hp – 1035hp to be exact. That, readers, is more than three times the factory output... Simon casually makes the point that he engine makes about 250 percent more torque than standard and revs 25 percent harder than standard.

Click for larger image

Peak power is achieved at around 6800 rpm with the rev limit currently set at 7500. This, believe it or not, is a relatively conservative tune and Simon says the engine has now reliably racked up more than 24 hours of full-throttle dyno time.

Despite already owing about AUD$45,000, Simon plans to reset the rev limit to around 8000 rpm and install a larger turbocharger to satisfy his new goal. A goal of 1000 kilowatts...

And what kinda driveline is gonna cop with this, you ask?

Click for larger image

“We’re planning a C9 auto trans and a stall converter of around 2500 rpm,” says Simon. Interestingly, Simon says there’s a good chance the factory diff should be able to cope with the strain – rear wheelspin will take some of the load off the diff gears.

We’ll be keeping a close eye on further development!

Contact:

Nizpro
+61 3 9761 1522
www.nizpro.com.au

1000HP Dyno Video

1000HP Ford XR6 Turbo Nizpro engine dyno

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
You don't need an expensive factory towbar harness - even on CAN bus cars.

DIY Tech Features - 4 August, 2009

Towbar Electronics

Part 1 of our major new series on understanding car electronics

DIY Tech Features - 2 December, 2008

How to Electronically Modify Your Car, Part 1

Do hybrid cars make sense?

Technical Features - 16 October, 2007

Alternative Cars, Part 6 - Hybrid

Testing vortex generators on slippery cars

Special Features - 18 October, 2006

Blowing the Vortex, Part 4

When not enough current is being produced

Technical Features - 14 July, 2009

Upgrading the Alternator

So what's detonation and how can it be detected?

DIY Tech Features - 2 November, 1999

DIY Detonation Detection Part 1

Fuel economy of 1 litre/100km from an amazing car

Technical Features - 11 June, 2002

The World's Most Fuel-Efficient Car

The $10 lathe or drill press tachometer

DIY Tech Features - 11 August, 2009

A Drill Press or Lathe Tacho

Reducing drag

DIY Tech Features - 10 July, 2012

Reducing the drag on square-back cars

Introducing a breakthrough in DIY electronics

DIY Tech Features - 6 October, 2009

eLabtronics EZ System, Part 1

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip