Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


The Story of Turbo'ing a Hybrid Prius, Part 3

The turbo might have worked, but the rest of the system was full of 'surprises'

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Trying to sort the mixtures
  • New fuel system
  • New intake and intercooler plumbing
  • Making a new airflow meter
  • Part 3 of 5
Email a friend     Print article
This article was first published in 2005.

Last week we got the turbocharged hybrid Prius on the road. The turbo was on, exhaust finished and air intake system working. But the initial testing showed that the air/fuel ratios were much leaner than desired – and much leaner than expected. So the next job was to sort out the fuelling – something more involved than it first appeared: solving the problem the first time was easy; solving the problem the second time was a nightmare.

Air/Fuel Ratios

I must admit that I was almost blasé about testing the air/fuel ratios: I was running a turbo’d 6 psi and the previously fitted supercharger had been producing much the same boost level, so I didn’t expect any change in air/fuel ratios. But after I inserted the MoTeC air/fuel ratio meter’s probe, I was shocked to find that at high loads, the mixtures were much leaner than expected. (The car used the approach covered in Altering Closed Loop Mixtures to switch it out of closed loop and then adjust the resulting mixtures. Basically this involves using a relay to disconnect the two oxy sensors at a certain engine load and then setting the resulting mixtures with the Digital Fuel Adjuster kit working on the airflow meter output.)

Clearly, 6 psi of boost from the turbo was sufficiently different than 6 psi boost from the supercharger to affect the air/fuel ratios - or perhaps the new intake and exhaust were making a huge difference?

Unlike when the blower was fitted, this time the lean mixtures were unable to be richened by adjustment of the Digital Fuel Adjuster (DFA) working on the airflow meter output. There were three possible reasons for this:

  • the airflow meter signal was as high as the ECU would accept
  • the fuel pump couldn’t cope
  • the injectors were running flat out (ie 100 per cent duty cycle)

At that stage I thought the latter was most likely, so I used a multimeter to measure the full-load duty cycle.  In fact, the duty cycle didn’t much exceed 60 per cent – it appears that in this car, that’s the ECU-fixed maximum injector flow.

Click for larger image

But this wasn’t initially clear and much fiddling later – including fitting a new fuel pump and modifying the in-tank regulator – I realised that I either needed bigger injectors, or higher fuel pressure to push more fuel through the factory injectors. I temporarily borrowed four injectors from a current Corolla (thanks Mr Avis for the hire car!) but found that despite their greater flow, the lower duty cycles of the Prius system resulted in mixtures that weren’t richer – they were in fact leaner!

Click for larger image

I then fitted a ‘black top’ Malpassi rising rate fuel pressure reg, with its diaphragm plumbed to the intake system before the throttle. To fit the regulator, a return line to the tank also needed to be installed and at the same time an external fuel filter was fitted. This upped off-load fuel pressure from the standard 44-50 psi to 60 psi and then caused an increase to 65 psi when on boost. Together with the oxy sensor switching, this resulted in stoichiometric mixtures (ie air/fuel of 14.7:1) being maintained until a full-throttle 2-3 psi was reached, with the mixtures then moving to 12.5:1 at higher loads.

Click for larger image

However, I then found a full-load misfire. I changed the plugs to one heat range colder and at the same time went to iridium (from NGK BKR5EY to BKR6EIX) but the miss remained. In the end I realised that the still connected Digital Fuel Adjuster had somehow been set with a minus 127 correction at a high load site – I must have bumped the unlocked hand controller without realising it. With the fuel map returned to zero correction, the miss went away... in effect, I’d been running a high load fuel cut! Ooops.

Intercooler and Intake Plumbing

Click for larger image

So far, all the test driving had been undertaken with intercooler (and inlet air) plumbing formed from copper 2-inch tube and fittings, insulated with thin foam rubber sheet and then covered in large diameter heatshrink. The use of copper pipe and fittings gives an easy push-together system that allows the pipework to be assembled and then taken elsewhere to be brazed, silver soldered or soft soldered. (The approach is covered in Copper Intercooler Plumbing) In the supercharger installation, the total length of copper piping was only about 50cm, but with the turbo positioned between the engine and the firewall, the pipe runs went up a lot in length.

And while I was happy with the appearance and functionality of short length of copper pipe and plumbing fittings, with several metres of plumbing now running around the engine bay, I wanted both a better appearance and also more gentle, flowing bends.

Making easier the decision to redo the plumbing was the fact that I’d bought a new friction cut-off saw (these days, extraordinarily cheap) and a secondhand arc welder. I didn’t intend doing all the welding with the arc machine (it’s very hard to weld thin gauge tube with an arc welder) but I thought that it would be straightforward to tack the tube together. Tube? Yes, I bought a heap of mandrel exhaust bends in both 2 inch and 1¾ inch sizes.

By using the cut-off saw and the arc welder, it was quite easy to come up with three completely new pipe runs – with the packaging flexibility of the bends (especially in the smaller 1¾ inch size), I decided to route the pipe in different directions to the previous approach. The tacked-together pipework was then taken to the local muffler shop for MIG’ing, before I spent a few hours at my belt sander grinding back the welds.

Click for larger image

I then had a local welder silver-solder brass fittings on the plumbing for two crankcase breather hoses, a boost feed to the rising rate fuel pressure reg, a boost feed to the wastegate, a water injection nozzle fitting, and the two connections for the recirculating blow-off valve. The next steps were sandblasting and then powder coating the plumbing.

Incidentally, if considering a similar plumbing approach, don’t disregard the significant costs - $120 for the mandrel bends, AUD$90 for the MIG welding, AUD$100 for the silver soldering, AUD$27 for the sandblasting, and AUD$50 for the powder coating. (So these bits of bent pipe ended up costing far more than the secondhand turbo!)

New Airflow Meter

Click for larger image

Up until now I’d been using the factory airflow meter, cut from the airbox into which it is normally integrated and mounted in-line after the new Falcon V8 airbox. However, its small size and the slightly bodgie way in which the chopped-up airflow meter fitted into the intake plumbing caused me to reconsider the approach. I decided to kill two birds with one stone and build a new, larger airflow meter that had proper in-line plumbing connections.

Click for larger image

The new airflow meter housing was made from a variety of PVC plastic plumbing adaptors, all available from the local hardware store. These were cut, filed, sanded and heated into shape, with the resulting airflow meter having a minimum internal cross-sectional area 31 per cent larger than standard. The airflow meter was located behind the right-hand headlight. The Digital Fuel Adjuster was then used to boost the airflow meter output signal so that the car ran as normal.

More Testing... and More Problems!

With the new intake and intercooler plumbing installed and the larger airflow meter in place, it was time to do some more testing. And to find still more problems...

The first issue was that the air/fuel ratios at high loads were again back to stoichiometric under full boost. That’s despite the increased fuel pressure, the switching out of the oxy sensors and minor tweaking with the Digital Fuel Adjuster. So why not do some major mixture tweaking with the DFA?

Well, even with the oxygen sensors disconnected, the Prius appears to have the ability to revert over time to standard mixtures. I think perhaps it can determine how much power the engine is developing via the hybrid control system and has a look-up table that correlates expected injector pulse widths with measured power. This results in gradual shift back to standard mixtures, even with the DFA making major changes to the airflow meter output signal.  This phenomenon was hard to isolate because it could be seen occurring only after a whole bunch of full-throttle events. Drive the car normally in closed loop and then nail it, and the mixtures would go satisfactorily rich. But repeatedly hammer the car up and down an (isolated!) test road and the full-throttle mixtures would gradually move from mid-twelves back to mid-fourteens.

Click for larger image

And there’s another complexity. The mixtures that occurred with the oxy sensors switched out depended to some extent on the correction that they’d been giving just prior to the switch-out. In other words, the long and short-term fuel trim values would affect what air/fuel ratios resulted with the oxy sensors switched out of the system. Perhaps it was this characteristic and the expected pulse widths for the given power that would then determine what air/fuel ratios the car ended up with?

The result was that full throttle air/fuel values could vary anywhere between 11:1 and 14.5:1. Do two full-throttle runs and the mixtures would be perfect – say 12.5:1. Then drive gently around the block and then hammer it... and the mixtures at full throttle would have changed to 14:1....

But what was the problem - hadn’t the mixtures been sorted earlier? That’s indeed the case – the problem reappeared only after the change in intake plumbing and the new airflow meter was fitted. It appears that these changes had further increased mass airflow – the engine was breathing better and better and the full-load mixture problem was getting worse.

Then yet another problem appeared. On the occasions when the mixtures were correct for full power, it was possible on the test road to hold full throttle for many seconds. And in this situation, a bizarre event kept occurring. After ten or so seconds, the electronic control systems of the car would momentarily close the electronic throttle! This could be seen on the vacuum/boost gauge which would dip from full boost to near full vacuum, before the throttle was again automatically opened. Perhaps some part of the hybrid system was being momentarily overloaded, which caused the system to reduce engine power?

Aaaaghhhh....

Next week: solving the final problems...

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
A breakthrough car that proved to be a step too far

Special Features - 6 August, 2008

The NSU Ro 80

The revs and loads at which engines use least fuel

Technical Features - 10 April, 2008

Brake Specific Fuel Consumption

Some of the different factory-fitted variable valve timing systems

Technical Features - 26 November, 2002

Variable Valve Timing

Converting a cheap car to battery electric power

Technical Features - 8 January, 2008

Electric Hyundai!

Easy - but only in retrospect!

DIY Tech Features - 28 June, 2011

Upgrading the Roomster's Front Brakes

Gorgeous and fast

Special Features - 3 June, 2014

The Auto Union Racing Cars

The Black Box is an electronic handling revolution

Technical Features - 10 February, 2009

Adjustable Stability Control!

So what's detonation and how can it be detected?

DIY Tech Features - 2 November, 1999

DIY Detonation Detection Part 1

Ideas that you can actually use in your home workshop

DIY Tech Features - 29 November, 2011

Real World Workshop Safety

How they built the fastest diesel on Earth

Special Features - 30 January, 2007

350.092 mph - Breaking the Diesel Speed Record

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip