Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Early Mercedes Safety

Some amazing archival material from Mercedes safety testing

By Michael Knowling

Click on pics to view larger images


This article was first published in 2006.

Mercedes-Benz is a world leader when it comes to automotive safety. The German company started passive safety engineering as early as 1939 and crash testing began in 1959. We take a look at some magnificent pics of Mercedes’ early safety development...

Click for larger image

From the late ‘50s, Mercedes came to the conclusion that full-scale testing was the most effective way to improve safety of their vehicles. This photo shows a 1951 170S following a frontal barrier test conducted at 50 km/h (note that the barriers were non-deformable until later years). The cabin shows good structural rigidity but, at the time, there was no consideration given to crumple zones and there was little to protect passengers.

Click for larger image

With poor road design and construction in the 1950s, it was relatively common for vehicles to roll over. So what better way to find out what happens than to high-speed barrel-roll a contemporary ‘50s Benz saloon? A special cork-screw ramp was used to get the car flying. This photo shows that the doors remained closed (partly thanks to Mercedes’ innovative ‘wedge pin’ locking system) though the boot lid has burst open.

Click for larger image

Also during the 1950s, Mercedes-Benz made seatbelts optional on the front seats. Initially, the objective was merely to prevent occupants being thrown out of the vehicle and, with this in mind, aircraft-type lap belts were deemed adequate. These lap belts were soon replaced by three-point seatbelts which also restrain the upper part of the body - this was particularly important at a time when there was little padding on the dashboard.

Click for larger image

This looks like trouble! In 1962, Mercedes adopted a steam rocket to accelerate the crash test vehicles to the desired speed. But things didn’t always go to plan...

Click for larger image

In this test, the rocket failed to brake at the correct moment and the car was slammed into the barrier at a higher speed than required. And, as evident by the crumpled rear-end, the wayward steam rocket also caused some damage of its own!

Click for larger image

In the mid ‘60s, following the introduction of crumple zones and a passenger-friendly interior, Mercedes developed the safety steering system. The new steering system involved locating the steering box further rearward (behind the front axle), a telescopically collapsible steering column and a large padded steering wheel boss. This arrangement went into production in 1968.

Click for larger image

Mercedes also introduced laminated safety glass windscreens to its passenger cars during the 1960s. Facial injuries (largely caused by people not wearing a seatbelt) were common in vehicles using a single-layer glass windscreen. This photo shows pendulum testing of a development windscreen.

Click for larger image

From 1972, the majority of crash testing was carried out in an indoor facility with controlled lighting. Offset barrier crash testing also become more common after Mercedes’ analysis of traffic accidents. The W126 S-class becomes the first car in the world designed from scratch to cope with asymmetrical frontal collisions.

Click for larger image

Vehicle occupants aren’t the only ones to benefit from Mercedes’ crash testing. A variety of different shape and size test dummies were run over by the late ‘70s W126 S-class. These tests enabled careful shaping of bumper bar, grille and bonnet emblem (with its spring loaded mechanism). And, as seen, the dummies were tested boots an’ all!

Click for larger image

The late ‘70s W126 S-class also benefited from adjustable height upper seatbelt anchorages and a host of safety features developed through Experimental Safety Vehicles (ESVs). Amazingly, airbag testing had begun as early as 1968 and, in 1980, a driver’s airbag was made available in the S-class. A front passenger airbag was added in 1987.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Using a prebuilt DIY electronic module to flash high intensity LEDs

DIY Tech Features - 14 July, 2008

Bike LED Lighting Power!

Perhaps the most sophisticated human powered vehicle you've ever seen

DIY Tech Features - 17 December, 2007

Air 150 Recumbent Trike, Part 1

Getting a great looking and durable finish

DIY Tech Features - 21 October, 2014

Powdercoating of fabricated parts

Making your own automotive themed clock

DIY Tech Features - 28 October, 2008

DIY Workshop Clock

Sounds ridiculous - but is it?

Technical Features - 4 October, 2007

Alternative Cars, Part 4 - Human Powered

Useful parts for nothing

DIY Tech Features - 6 October, 2009

Getting the Good Parts from Scanners!

DIY flow testing of the intake

Technical Features - 31 July, 2008

Free-Flowing a Miata MX5

Organising storage

DIY Tech Features - 17 April, 2012

A New Home Workshop, Part 8

Some aspects of fast driving never change...

Special Features - 15 September, 2009

Fast Past

Want to see where you're going with modifications? Measure the airflow meter output.

DIY Tech Features - 20 January, 2005

Using the Airflow Meter as a Dyno

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip