For whatever reason, pre-BA Fords aren’t the most popular performance
machines. Sure, they’re home-grown for Aussie conditions, roomy, tough and
grunty, but the big Fords always play second fiddle to the Holden rival.
But to Grant Ward of Brisbane there’s nothing other than a Ford. Grant has
owned an ED Falcon with bolt-on mods, an EL XR6 with similar tweaking and now
this – a 320kW ATW Windsor 5.0 litre AUII XR8!
Grant says the step up to an AUII XR8 was a natural progression – the fact
it’s a V8 and relatively late model made it the ideal machine to replace his
much loved XR6. The performance and on-road feel of the XR8 is described by
Grant as "fine" but, of course, old habits are hard to break. It wasn’t long
before the XR8 was being transformed from standard bit by bit...
Initially, Grant’s mods were limited to aesthetics – Avanti 18 x 8.5 inch
alloys with 265 and 255mm low profile Bridgestone S-03s complemented by superlow
King springs. A set of Koni adjustable dampers and new polyurethane bushes were
also included.
The next step was to unleash the Windsor V8’s grunt and give it a bit of a
growl. A pair of Pacemaker Tri-Y headers was bolted to the heads and the rest of
the system was fabricated by D&T Performance in Adelaide. The system employs
twin high-flow cats, twin 2 ½ inch mandrel pipes leading into a single 2 ½ inch
pipe over the axle. In light of the extra power that’s now generated, the rear section has since been replaced with a single 3
inch.
With the headers, exhaust and a K&N filter bunged in, Grant’s XR8 picked up around 5kW ATW for a total of 140kW at the wheels on Bob
Romano’s Dyno Dynamics chassis dyno (Bob and his son, Chris, can be thanked for
the majority of work on the car).
At this point Grant looked at his options and decided the next step should be
to optimise the management system to suit the mechanical mods. A UniChip
interceptor was fitted to the Ford loom and, once tuned, improved
drivability along with an extra 10kW - one-fifty was seen at the wheels. This
was quickly followed by a mild camshaft upgrade that gave a slight improvement
at high revs without sacrificing idle quality or bottom-end torque.
With this sort of power output, the factory intake manifold becomes a
considerable airflow restriction. There are various bolt-on replacement
manifolds – but why bother with that approach when you can literally
force air through the stock manifold?
Grant hunted down a new CAPA (Centrifugal Air Pumps Australia) Vortech V2
supercharger complete with all necessary brackets, belts, air intake, Bosch
blow-off valve, upgrade fuel pump and water injection. Bob Romano and his team
were handed the job of installation and the XR8 immediately responded with a
considerable 230kW at the wheels. Note that this was achieved on 10 psi peak
boost with the standard camshaft reinstalled.
With some mucking around ‘high flowing’ the injectors, sorting the
pre-compressor intake and retuning the existing UniChip, power rose to 280kW ATW.
Now we’re talkin’!
With these mods fresh under the bonnet, the standard clutch began slipping –
understandably. Grant upgraded to a still-streetable heavy-duty clutch/steel
flywheel combo along with a ‘ripper shifter’ on top of the standard T5 gearbox.
At the squealing end you’ll find a shorter 3.73:1 Ford LSD. Oh, and at about
this time a set of EBC Green Stuff brake pads and DBA discs were thrown on.
And Grant was pretty happy for the car to remain like this.
For a while.
The camshaft and cylinder heads were the next area of improvement. Trickflow
aluminium bolt-on heads were fitted to the standard block along with the
associated rocker arms, pushrods, valves and valve springs. A genuine ‘B303’
Ford Motorsport camshaft and timing chain set also went in along with an upgrade
fuel system – namely, bigger injectors, a Bosch Motorsport pump and Vortech
progressively rising rate fuel pressure regulator. Interestingly, Grant also
installed Phenolic manifold insulators to help prevent heat soak issues.
With no extra boost pressure (still 10 psi peak) Grant’s XR8 has delivered
320kW at the wheels on the Romano chassis dyno. What’s more, Grant says it’s
anything but a pig – it gets driven every day in all temperatures, fills with
fuel at the local servo and has performed problem-free. The only hiccup was the
supplied pre-compressor pipe was ‘sucked in’ at high loads; this pipe has
since been replaced with a custom set-up. The Romano’s also elected to switch to
higher quality blower lubrication fittings and silicone pipes.
Both Grant and the Romanos agree the car is pushing the limits of the stock
engine internals. Without an intercooler to reduce intake air temperature,
there’s always the risk of detonation, but some careful tuning and in-house
modification of the CAPA water injection system prevent undesirable combustion
behaviour.
So without any bottom-end strengthening, the car has ran a best quarter mile
time of 12.6 seconds at 115 mph. Note that this was using the street
Bridgestones which Grant says are great – but they’re a long way off slicks.
With more grip, a low 12 seems likely.
But isn’t it time to upgrade to a BA Ford?
Well, in all probability he’ll keep this beast – the cost of buying a new car
with similar performance would be astronomical. Instead, Grant wouldn’t mind
adding an intercooler or maybe a 6 speed – or maybe a stroker crank.
Whatever way he goes, you know it’ll be Game On against anyone that pulls
alongside in a ‘hot’ Holden....
Contact/Thanks:
Bob Romano Performance +61 7 3395 8255
www.bobromano.com.au
Grant would like to thank Bob and Chris Romano and the rest of the team.
Did you enjoy this article?
Please consider supporting AutoSpeed with a small contribution. More Info...
|
More of our most popular articles.
|
|
|
Email a friend
Print article
|