Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Project Honda Insight, Part 8 - Building the Exhaust

Making a complete turbo exhaust in a home workshop

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Exhaust built DIY at home with mandrel bends
  • Holden cat converter, Jaguar muffler and Ferrari exhaust butterfly!
  • Ovalised, mandrel bent dump pipe
Email a friend     Print article
Click for larger image

This series is based around a 2001 model hybrid Honda Insight.

The Insight remains one of the most aerodynamic and lightest cars ever made, with a Cd of 0.25 and a total mass of about 850kg from its 2-seater aluminium body.

The intent of the project is to turbocharge the engine, add water/air intercooling and programmable engine management, and then provide new high voltage batteries and a new electric motor control system.

The aim is to build a car with the best performance/economy compromise of any in the world.

The series so far:

Project Honda Insight, Part 1 – Introduction

Project Honda Insight, Part 2 – Fitting an Alternator

Project Honda Insight, Part 3 – Building an Airbox

Project Honda Insight, Part 4 – Intercooling Requirements

Project Honda Insight, Part 5 – Intercooling System #1

Project Honda Insight, Part 6 – Intercooling System #2

Project Honda Insight, Part 7 - Turbocharging

This issue: building the exhaust

The rationale for the exhaust design was pretty simple - excellent flow with adequate noise suppression. But like nearly all things to do with this project, there were subtleties and other factors that made it more interesting than most off-the-shelf modifications.

Design

Remembering that the Insight’s engine is only 1 litre in size, and that even with turbocharging it’s not expected that power will be greater than about 75kW or so, a relatively large tube size was selected for the exhaust – 2 inch (50 mm). (This compares to the standard exhaust pipe diameter, that over most of its length is just 1.4 inches.)

A 2-inch exhaust, made from mandrel bends and using an appropriately flowing cat converter and muffler, has a cross-sectional area double the standard exhaust – and so should flow absolutely heaps for the power being developed.

Click for larger image

The use of 2 inch piping had two further advantages. Firstly, the 2-inch pipe could still be fitted under the car within the original exhaust recess. (The bottom of the Honda is largely flat for aerodynamic reasons, so taking another route with the pipe wouldn’t be a good idea). Secondly, I had available a muffler, cat converter and exhaust butterfly that would work with this size pipe.

Off the turbo, the exhaust pipe takes a long 90-degree (ovalised) bend as it squeezes past the alternator; this is then followed by two 90-degree bends before the pipe exits under the car, parallel with the floor pan and facing backwards. A stainless steel flex section is installed at this point, catering for the transverse engine’s movement under load.

The cat converter immediately follows the flex section, after which there is about a metre of straight pipe that then connects to three 45-degree bends that take the gases under the rear torsion beam axle to the muffler, located just prior to the back of the car.

Bolted to the rear of the muffler is a variable flow control valve that connects in turn to a short tail pipe exiting at the factory location of a hole in the lower bumper cover.

Dump pipe

Not being easily available from commercial sources, the exhaust flange for the turbo dump was made from scratch. It was rough-cut from 8mm plate using an oxy acetylene and then ground, filed and drilled to the correct profile.

Click for larger image

The dump pipe off the turbo was built no less than four times. The difficulty was in squeezing past the alternator while still clearing the steering arm. The steering arm is at its most difficult position at full suspension droop and with full right-hand steering lock.

(The fact that for the car to be in a situation where it’s at full suspension droop and at the same time is on full steering lock would mean that a knocking exhaust would be the least of my worries [ie I’d be airborne trying to avoid a pole or some such] is not the point: the dump pipe shouldn’t be able to foul anything under any circumstances...)

The first version of the dump used a normal 180-degree, 2-inch mandrel exhaust bend off the flange. This was neat, cheap and simple. However, it turned out that it didn’t give the required clearances.

The next version mixed a steam pipe (ie heavy wall) 90-degree bend off the turbo with normal exhaust pipe bends after that. However, the exhaust pipe needed to be shaped into a rectangular cross-section to get past the steering arm and alternator; this in turn reduced internal cross-sectional area at that point.

The next version used larger diameter steam pipe bends cut, welded and shaped to give the required clearance. However, the greater wall thickness meant that the internal cross-sectional area became too small.

Click for larger image

The final version uses a 2.5 inch, 180 degree mandrel bend. This bend was ovalised in my press, being first filled with sand to help it hold its shape. The use of a larger diameter tube maintains cross-sectional area, even when it is flattened as was required to clear the steering tie rod and alternator.

At the end of the ovalised bend, the exhaust transitions to 2 inch pipe via short fabricated cone. It then passes through two 90-degree bends before this section of the exhaust ends in two-bolt flange. The use of the flange allows the exhaust to be easily removed from the car in two pieces.

Click for larger image

A strong brace (arrowed) connects the exhaust after the turbo to the alternator mount; this brace is used to reduce the loads occurring on the three 8mm studs that hold the turbo exhaust manifold to the head. In effect, the turbo is supported by three head studs, plus the four mounting bolts of the alternator bracket.

The wide-band oxygen sensor is also mounted on this section of pipe.

Click for larger image

This first section of exhaust is lagged. This gives faster light-up of the cat and also protects close-mounted engine bay components from heat.

Exhaust

The majority of the exhaust length was made up of pre-formed mandrel bends. In the past, mandrel bends have cost a proverbial arm and leg but these days, through the joys of eBay, they’re quite cheap. The exhaust used eight mild steel mandrel bends at a typical cost of AUD$11 each.

Click for larger image

The cat converter is a stainless steel unit from a Holden Commodore V8, bought second-hand from a low kilometre car for nearly nothing. The car originally used two of these cats, so each is sized to flow well over 100kW.

Click for larger image

A heat shield was fitted to the upper part of the cat that is relatively near the underbody. The heatshield is held in place with stainless steel cable ties.

Click for larger image

The muffler – just a single one is used – is a resonator from a supercharged Jaguar XJR100. A friend gave a pair of these to me a few years ago; again, they’re made of stainless steel. Despite being a straight-through design, they suppress noise very well.

Click for larger image

The tricky part of the exhaust is the rear-mounted butterfly. This was sourced from a Ferrari 575M - in that car, these butterflies are used to vary the flow from the second outlet of each of two mufflers. In the Honda, the butterfly is placed so that all exhaust flow has to pass through it.

As we have described previously (for example, see Pure Pipe Perfection 2 - Introducing the Secret Weapon...), as exhaust backpressure rises, noise reduces. In addition, as backpressure rises, the cat converter comes up to operating temp more rapidly.

In the Honda’s exhaust design, where the (relatively) large diameter mandrel bends, high-flowing cat converter and a straight-through resonator are likely to pose very low restriction, the butterfly will be used to provide low noise levels at low loads, opening-up as engine load increases. The minimum opening of the butterfly will be set by an adjustable screw. (It’s intended that the butterfly be electronically controlled by a servo – more on this in a later story.)

The exhaust was MIG welded together. It was built with the car placed only on jack-stands (rather than a hoist) – at times uncomfortable, but still quite possible while working at home.

Conclusion

Click for larger image

The exhaust was relatively low in cost, should flow extremely well, and with the use of the variable butterfly, can be tuned to provide whatever combination of flow and noise level is required at different loads.

Next: Starting the turbo engine, and moving the 12V battery

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
A brilliant do-it-yourself handheld spotlight or bike headlight

DIY Tech Features - 11 February, 2008

Building a High Performance LED Lighting System, Part 1

Designing for body stiffness

Technical Features - 14 December, 2010

One Very Stiff Body!

Techniques to revolutionise your car modification

DIY Tech Features - 31 March, 2009

Ultimate DIY Automotive Modification Tool-Kit, Part 1

The frame, seat and chain path

DIY Tech Features - 16 June, 2009

Chalky, Part 6

The electric motor and control system for a DIY electric bike

DIY Tech Features - 11 February, 2005

Building an Electric Bike Part 2

Some techniques for making your custom constructions lighter

DIY Tech Features - 10 August, 2010

Lightening Parts

Building your own 270 watt home sound amplifier

DIY Tech Features - 14 May, 2013

Building a home sound amplifier, Part 2

If you're designing a vehicle, some very simple calculations can tell you a lot

Technical Features - 14 April, 2009

The Moment Has Come...

An extraordinary engine that was light, powerful and fuel-efficient

Special Features - 5 March, 2013

Napier Nomad

A press so huge it can forge titanium beams over 5 metres long

Special Features - 29 October, 2013

The Wyman Gordon 50,000 ton forging press

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip